The Spot Zero Mobile Pro and Spot Zero Mobile Pro Mini are portable reverse osmosis water purifiers. They remove up to 99% of dissolved solids, so you can rinse a boat and let it air dry without water spots, or fill the boat's water tank. The Mobile Pro is sized for boats about 40–85 ft; the Pro Mini for boats up to about 45 ft.

These directions follow Spot Zero's published manuals, data sheets and product pages. Always read the label, manual and Safety Data Sheet for your product, and test a small area first.

Before you hook up

  • Dock water pressure: at least 10 psi and no more than 85 psi.
  • Water and air temperature: 40–100°F. Never run or store the unit below freezing; freeze damage isn't covered by the warranty.
  • Power: 115 V, into a GFCI-protected, grounded outlet. Use a 12-gauge or heavier extension cord.
  • Hoses: use hoses rated to at least 150 psi, and keep them as short as possible. The maximum is 25 ft.
  • If your dock water has a lot of chlorine or sediment, Spot Zero recommends adding the Spot Zero Portable Dockside Pre-Filter Assembly.

Setup

  1. Connect the dock hose to the TAP WATER FEED INPUT port.
  2. Connect your rinse hose to the SPOT ZERO OUTPUT port.
  3. Make sure the discharge (concentrate) hose is attached, unrestricted and draining freely to an open area. A blocked discharge can permanently damage the membranes.
  4. Plug the unit into a GFCI-protected outlet.

Start-up and use

  1. The display shows STANDBY once it has power.
  2. Turn on the dock water. The unit purges air, then shows PRIMING, READY and RUNNING.
  3. When it shows RUNNING, it's ready. For a boat rinse, most users put a spray nozzle on the output for more reach. To fill a tank, remove the nozzle for maximum flow.
  4. If the output stays closed for more than 10 minutes, the unit goes back to Standby.

Cold water lowers output, so expect less flow on cool mornings.

Shutdown

  1. With the unit RUNNING, close the output with your nozzle or an in-line valve.
  2. The unit starts an auto-flush. Let it run uninterrupted for 3 minutes.
  3. Turn off the dock water. The unit shuts down on its own. A brief "!LOW FP!" message is normal.
  4. Unplug it, disconnect both hoses and put the storage caps back on the ports.

Run or flush the unit for at least 5 minutes every month to keep the membranes from fouling.

Changing the pre-filter

The display reminds you: ORDER FILTER at 90 hours, CHANGE FILTER at 100 hours, and FILTER PAST DUE at 110 hours. Never clean and reuse a filter. For the Mobile Pro, the replacement is the Spot Zero Mobile Pre-Filter; call us to confirm the right part for your model.

  1. Turn off the water, disconnect the hoses and unplug the unit.
  2. Remove the 6 end-plate screws and pull out the old filter.
  3. Slide in the new filter in the direction of the arrow, white seal last. Check the O-rings are seated, and hand-tighten the screws.
  4. Run water for about 30 seconds to bleed the air.
  5. Shut the water off and let the cleaner built into the new filter soak for at least 30 minutes, but no more than 24 hours.
  6. Flush for 10 minutes with the output closed and the unit unplugged.
  7. Reset the filter hours on the display.

Membranes are replaced when the display reminds you, or when the purified water is no longer much cleaner than the feed water. Replacement membranes: Spot Zero 4041 Membrane (Mobile Pro) and Spot Zero Mobile Pro Mini Membrane.

Storage and winterizing

  • Best: keep the unit in a heated space above 32°F and still run it 5 minutes every month.
  • Not using it for more than a month: Spot Zero's procedure replaces the water in the membranes with CH-03 membrane storage solution, mixed into 5 gallons of Spot Zero product water (never tap water) and circulated with a small auxiliary pump. Never plug the unit in during this process.
  • Unheated storage: the same procedure, using a mix of product or distilled water and non-toxic propylene glycol. Never use ethylene glycol.
  • Back in service: install a new pre-filter, connect the hoses, and flush for about 30 minutes with the unit unplugged, sending that water overboard. Then plug in and run as normal.

The storage steps have several specific mix ratios and pump limits. Follow the manual or the Spot Zero video below, or bring the unit by and we'll walk you through it.

Safety

  • Only plug into a grounded, GFCI-protected outlet with a correctly rated cord.
  • Never run the pump dry, and never let the unit freeze.
  • Water from the recommissioning flush is not drinkable.

Watch it done

Questions before you start? Call or stop by Marine Detail Supply Company Fort Lauderdale, 2821 SW 23rd Terrace, Unit 1, just off SR 84 near Marina Mile. Open Mon–Fri, 8am–4pm. (754) 732-1937. Orders over $200 ship free in the domestic US.

November 16, 2026 — Marine Detail Supply Team