How to Apply Starke Liquid THOR Nano Ceramic Coating
Starke Liquid THOR is a marine-grade SiO2/TiO2 nano ceramic coating with a long working time. STARKE approves it for gelcoat, marine paint, glass, metal, vinyl, plastic and isinglass. It works best as the topcoat over Starke Repel Pro, and can also be used on its own.
These directions follow STARKE's published product pages and Technical Data Sheets. Always read the label and Safety Data Sheet on your bottle, and test a small area first.
Products in this guide
What you'll need
- Starke Liquid THOR
- Coating applicators with a plastic barrier, such as Autofiber Thin Coating Applicators
- Two clean premium microfiber towels per section, such as Autofiber Ultra Plush Microfiber towels or the Dual Pile Microfiber 36 Pack. Cut off the plastic tags first.
- Starke Surface Prep Alcohol Spray
- Nitrile or rubber gloves, chemical splash goggles, and masking tape to mark sections
Before you start
- Never coat over oxidation. The surface must be compounded and polished first, even on a new boat. Remove all old wax and sealant.
- Wash the boat, then wipe with Starke Surface Prep Alcohol Spray until the surface is completely oil-free.
- Temperature: 60–90°F. Do not apply below 50°F.
- Work in the shade if you can. Sun, heat and wind shorten the flash time; humidity lengthens it.
Step by step
- Mark out a section with tape. THOR's long working time allows larger sections, but keep them conservative until you're comfortable.
- Prime the applicator with several drops of coating and fold it to spread the product.
- Apply in a box pattern: edges first, then the interior, with overlapping strokes and even pressure.
- Watch for the flash. It usually takes 5–10 minutes. You'll see an iridescent, oil-slick or "sweating" look.
- Level and remove with the two-towel method: the first towel takes off the excess, and a clean "insurance" towel makes a final pass for high spots.
- If a section goes past its flash window, immediately reapply coating to that section and remove it at the proper flash time. Never force removal.
Layering with Repel Pro
STARKE's recommended system is one layer of Starke Repel Pro as the base and one layer of THOR on top. Let Repel Pro sit 1.5–3 hours, then apply THOR within 1.5–6 hours of the Repel layer (about 10 hours at most). Two coats of THOR is also an option.
Cure
- Keep it dry for 24 hours minimum, 48 hours ideally. If rain is coming, you need at least 2–4 hours before it hits. If it does get wet, don't rub it dry.
- No soap washes for 5–7 days. A light rinse is fine before then.
Found a high spot after it cured? Work it with Starke Triple P Ceramic Prep Polish, wipe with Starke Surface Prep Alcohol Spray, and recoat that area.
Maintenance
- Wash with a pH-neutral soap such as Starke Pure Clean Boat Soap or Starke Ultra Clean SiO2 Soap, and use Starke Salt Clean Boat Wash after salt runs. Don't use soaps that contain wax.
- Use microfiber wash mitts, not brushes, on smooth surfaces.
- Rinse with deionized or RO water when you can.
- Every 9–12 months: a Starke Venom Water Spot and Stain Remover strip wash, a quick Starke Triple P Ceramic Prep Polish polish, a Starke Surface Prep Alcohol Spray wipe, then one fresh layer of topcoat.
Top up with Starke Replenish Silica Spray monthly in active saltwater, or quarterly in fresh water. STARKE does not recommend putting wax on top.
With Repel Pro underneath, expect 12–24 months of protection, depending on use, storage and upkeep.
Safety
- Corrosive and highly flammable. The STARKE SDS lists THOR as DANGER: it causes severe skin burns and eye damage.
- Wear nitrile gloves and chemical splash goggles the whole time. Add a face shield and chemical-resistant sleeves or apron where splashing is possible.
- Use only with good ventilation, never in a confined space.
- Keep away from heat, sparks and flame. Store cool, tightly closed and locked up.
- Keep it in its glass bottle; the coating reacts with plastic.
Watch it done
- Ultimate Guide to Ceramic Coat a Boat (Surface Prep, Repel Pro, THOR)
- Ceramic coat non-skid and vinyl wrap
Questions before you start? Call or stop by Marine Detail Supply Company Fort Lauderdale, 2821 SW 23rd Terrace, Unit 1, just off SR 84 near Marina Mile. Open Mon–Fri, 8am–4pm. (754) 732-1937. Orders over $200 ship free in the domestic US.




